Voge 650DSX
650DSX Torque specifications
Tightening torques by model, taken from the factory documentation. Always cross-check against your own manual.
This page lists bolt tightening torques. The 650DSX engine itself produces 60 Nm @ 5,500 rpm. All specifications
Choose "Save as PDF" in the print dialog to keep a copy.
Wheels and brakes
| Fastener | Thread | Torque | Notes |
|---|---|---|---|
| Front wheel axle | M18 | 75Nm55.3lb-ft | - |
| Front brake disc | M8 | 35Nm25.8lb-ft | - |
| Rear wheel axle nut | M20 | 95Nm70.1lb-ft | - |
| Rear brake disc | M8 | 35Nm25.8lb-ft | - |
| Chain adjuster nut | M8 | 9Nm6.6lb-ft | - |
| Rear sprocket bolt and nut | M8 | 35Nm25.8lb-ft | - |
| Front sprocket bolt | M10 | 55Nm40.6lb-ft | - |
| Chain slider bolt | M6 | 4.5Nm3.3lb-ft | - |
| Brake caliper dust cover | M6 | 9Nm6.6lb-ft | - |
| Brake pad guide pin | M8 | 25-30Nm18.4-22.1lb-ft | - |
| Brake bleed screw | M8 | 3.9-6.9Nm2.9-5.1lb-ft | - |
| Brake hose banjo bolt | M8 | 30-40Nm22.1-29.5lb-ft | - |
| ABS hose bolt | M8 | 21-27Nm15.5-19.9lb-ft | - |
| Speed sensor ring screw | M6 | 9Nm6.6lb-ft | - |
Chassis and suspension
| Fastener | Thread | Torque | Notes |
|---|---|---|---|
| Swingarm pivot | M14 | 120Nm88.5lb-ft | - |
| Rear shock absorber, upper mount | M12 | 60Nm44.3lb-ft | - |
| Rear suspension linkage (shock, linkages, frame and swingarm) | M12 | 60Nm44.3lb-ft | - |
| Handlebar clamp bolt | M8 | 18Nm13.3lb-ft | - |
| Upper triple clamp locking bolt | M22 | 90Nm66.4lb-ft | - |
| Side stand | M10 | 40Nm29.5lb-ft | - |
| Side stand kill switch bolt | M6 | 6Nm4.4lb-ft | - |
| Centre stand shaft nut | M10 | 40Nm29.5lb-ft | - |
| Rear brake pedal bolt | M6 | 9Nm6.6lb-ft | - |
| Rear brake master cylinder bolt | M6 | 9Nm6.6lb-ft | - |
Engine and exhaust
| Fastener | Thread | Torque | Notes |
|---|---|---|---|
| Engine mount, front upper | M10 | 60Nm44.3lb-ft | - |
| Engine mount, front middle | M10 | 50Nm36.9lb-ft | - |
| Engine mount, front lower | M10 | 50Nm36.9lb-ft | - |
| Engine mount, rear lower | M10 | 50Nm36.9lb-ft | - |
| Engine mount, left upper | M10 | 50Nm36.9lb-ft | - |
| Engine mount, right upper | M10 | 50Nm36.9lb-ft | - |
| Engine left rear cover | M6 | 9Nm6.6lb-ft | - |
| Oil filter cover | - | 10Nm7.4lb-ft | - |
| Coolant drain bolt | M6 | 6Nm4.4lb-ft | - |
| Radiator mounting bolt | M6 | 9Nm6.6lb-ft | - |
| Exhaust header nut at the engine | M8 | 22Nm16.2lb-ft | - |
| Muffler front connecting bolt | M8 | 22Nm16.2lb-ft | - |
| Muffler connecting sleeve bolt | M8 | 22Nm16.2lb-ft | - |
| Muffler rear mounting bolt | M10 | 35Nm25.8lb-ft | - |
| Muffler rear mounting bolt, small | M8 | 9Nm6.6lb-ft | - |
| Oxygen sensor | - | 40Nm29.5lb-ft | - |
| Engine shield bolt | M6 | 6Nm4.4lb-ft | - |
| Air filter cover screw | ST4.8 | 2Nm1.5lb-ft | - |
| Air filter case halves | ST4.8 | 2Nm1.5lb-ft | - |
| Air filter case to throttle body | M5 | 6Nm4.4lb-ft | - |
| Battery terminal bolt | M6 | 6Nm4.4lb-ft | - |
Bodywork and fittings
| Fastener | Thread | Torque | Notes |
|---|---|---|---|
| Fuel tank mounting bolt | M8 | 18Nm13.3lb-ft | - |
| Fuel tank lock bolt | M5 | 6Nm4.4lb-ft | - |
| Fuel level sensor nut | M6 | 9Nm6.6lb-ft | - |
| Fuel line clamp | M5 | 4.5Nm3.3lb-ft | - |
| Carbon canister bolt | M6 | 6Nm4.4lb-ft | - |
| Coolant expansion tank bolt | M6 | 9Nm6.6lb-ft | - |
| Crash bar mounting bolt | M8 | 35Nm25.8lb-ft | - |
| Body panel bolt | M6 | 6Nm4.4lb-ft | - |
These figures are published for reference and are not official Voge data. Confirm each one in the service manual for your model and model year, tighten with a calibrated torque wrench, and have a qualified mechanic do the work if you are unsure.
Source: Voge 650 Series service manual (R8100, October 2021), the Parameters table at the end of each chapter · Updated Sep 5, 2026
